| 4、泵的材料說明Instmetion of Pump’S Materials．
泵根據使用情況，將過流零件的材料分為用于海水和用于淡水兩類，用戶在定貨時應在合同予以說明。用于海水時，過流部件采用耐海水腐蝕的銅質材料，軸為不銹鋼；用于淡水時，過流部件采用球墨鑄鐵或灰鑄鐵，軸為不銹鋼。
The pump
call be cataloged into two kinds，one is suitable for sea water,another for fresh water according to
the different materials contacted with liquid．Please
make a note in the ordering agreement．Any parts which
contact with sea water are made of anti-sea water corrosive materials，i.e．，copper,shafts of Pump are made of
stainless steel when the pumps are intended to be used for sea water．Parts which contact with fresh water are made of graphite cast iron，shafts ofpump are made of stainless steel when the pumps are
intended to be used for fresh water．
5.1運轉前準備Preparationbefore running
5.1.1泵首次啟動前應盤動數圈(可拆開電機風扇護罩盤動風扇)，確信轉動靈活無碰擦現象后，往泵內注滿液體，并打開進出口管路閥門(進口全開)。
注意：泵內未注滿液體前，不能啟動電機，否則軸封干磨失效!
Before starting the pump，turn the coupling for
circles(turn the fan of．electric motor after removing
the cover)，and make sure that it call revolve smoothly,then
fill the liquid into the pump till being full and open the valves of
inlet&outlet piping(valves of inlet open completely)．
Attention：The electric motor Can not
be switched on until the pump full of liquid otherwise the sealing of shaft
will be in failure due to dry-friction．
5.1.2點動電動機，檢查電動機轉向是否符合泵的轉向標志。
Touch the switch of electric motor
and make sure that the direction ofthe pump is correct(same as the notation
indicated on the pump body)．
5.2運轉中注意事項Precautionduringoperation
5.2.1泵起動后，有一個自吸排氣過程，一般在2～3分鐘內完成。
It spends two to three
minutes to finish the self-suction and discharge after the pump starts．
5.2.2泵開始排水后，逐漸調節出口閥門，直到規定出口壓力為止。
Adjust gradually the outlet
valve until the specified outlet pressure is reached
After the pump begins to discharge．
5.2.3泵應保持制造廠推薦的允許流量范圍內運轉。此范圍一般為額定流量的50％-120％，注意不要在關閉出口閥門狀態下長時間運轉。
How of the pump should be
kept within the allowable extent recommended by the manufacture．This extent is generally
to be 50％to 120％of the rated
flow．Take care that do not operate the pump for a long
time when the outlet valve turns off．
5.2.4注意軸承溫升，軸承體外表溫度一般不超過75℃，軸承溫升不超過35℃。
Take care of the temperature
rise of the bearings．Surface temperature of the
|